Lesson 42 of 46 · Physics

Magnetism and electromagnetic induction

Magnetic forces on moving charges and currents, the fields that currents make, magnetic flux, Faraday and Lenz induction, generators and transformers.

About 22 minutes

In this lesson

  • Calculate the magnetic force on a moving charge and on a current-carrying wire, and explain why it does no work on a charge.
  • Describe the fields made by a straight wire and a solenoid, and calculate magnetic flux.
  • Use Faraday's and Lenz's laws for induced emf, and the turns ratio of an ideal transformer.

The idea

Magnets and magnetic fields

A magnet has a north pole and a south pole. Like poles repel and unlike poles attract, and a pole never appears on its own: cutting a bar magnet in two gives two smaller magnets, each with both poles. The field round a magnet is drawn with field lines that leave the north pole and enter the south pole outside the magnet; a compass needle lines up along them. The Earth behaves like a large magnet whose magnetic south pole lies near the geographic North Pole, which is why the north end of a compass points north.

The magnetic field BB is measured in tesla (T). Between the poles of a strong laboratory magnet it is of the order of 0.1 to 1 T; the Earth's field is about 5×10−5 T5 \times 10^{-5}\ \text{T}.

The force on a moving charge

A charge qq moving with speed vv at an angle θ\theta to a magnetic field BB feels a force

F=qvBsin⁡θ.F = qvB\sin\theta.

The force is perpendicular to both the velocity and the field. It is greatest when the charge moves at right angles to the field and zero when it moves along the field. Its direction for a positive charge is given by the right-hand rule: with the fingers of a flat right hand along BB and the thumb along vv, the palm pushes in the direction of FF. For a negative charge, such as an electron, the force is in the opposite direction.

Because the force is always perpendicular to the velocity, it does no work: it changes the direction of motion but never the speed or the kinetic energy. A charge moving at right angles to a uniform field therefore travels in a circle, with the magnetic force providing the centripetal force:

qvB=mv2r⇒r=mvqB.qvB = \frac{mv^2}{r} \quad\Rightarrow\quad r = \frac{mv}{qB}.

The force on a current-carrying wire

A current is moving charge, so a straight wire of length LL carrying a current II at an angle θ\theta to a field BB feels a force

F=BILsin⁡θ,F = BIL\sin\theta,

again perpendicular to both the wire and the field. This is the principle of the electric motor: the two sides of a current-carrying coil in a magnetic field are pushed in opposite directions, which turns the coil.

Fields made by currents

Every current produces a magnetic field. Round a long straight wire the field lines are circles centred on the wire, and the field at a distance rr is

B=μ0I2πr,μ0=4π×10−7 T m/A.B = \frac{\mu_0 I}{2\pi r}, \qquad \mu_0 = 4\pi \times 10^{-7}\ \text{T m/A}.

The right-hand grip rule gives its direction: point the thumb along the current, and the curled fingers show the direction of the field lines. Inside a long solenoid with nn turns per metre the field is nearly uniform, B=μ0nIB = \mu_0 n I, and outside it the field looks like that of a bar magnet. Two parallel wires carrying currents in the same direction attract each other; with currents in opposite directions they repel.

Magnetic flux

The magnetic flux through a flat area AA in a uniform field BB is

Φ=BAcos⁡θ,\Phi = BA\cos\theta,

where θ\theta is the angle between the field and the normal to the area (the line perpendicular to its surface). Flux is measured in webers (1 Wb=1 T m21\ \text{Wb} = 1\ \text{T m}^2). It is greatest when the field passes straight through the surface and zero when the field lies along it.

Electromagnetic induction

A changing magnetic flux through a circuit induces an electromotive force (emf). For a coil of NN turns, Faraday's law gives

ε=−NΔΦΔt.\varepsilon = -N\frac{\Delta\Phi}{\Delta t}.

The flux can change because the field changes, because the area changes, or because the coil turns. A steady flux, however large, induces nothing. A straight rod of length LL moving at speed vv at right angles to a field BB has an emf ε=BLv\varepsilon = BLv between its ends.

The minus sign expresses Lenz's law: the induced current flows in the direction that opposes the change producing it. Push the north pole of a magnet into a coil and the near end of the coil becomes a north pole, repelling the magnet. You must do work to push it in, and that work becomes electrical energy: Lenz's law is conservation of energy at work.

Generators and transformers

A coil turning in a magnetic field has a flux through it that rises and falls, so it produces an alternating emf: this is a generator. A transformer has two coils wound on a shared iron core. An alternating current in the primary coil produces a changing flux in the core, which induces an emf in the secondary coil. For an ideal transformer

VsVp=NsNp,VpIp=VsIs.\frac{V_s}{V_p} = \frac{N_s}{N_p}, \qquad V_p I_p = V_s I_s.

A step-up transformer raises the voltage and lowers the current by the same factor; it does not create power. A transformer does not work with a steady direct current, because a steady current makes a steady flux. Electricity is transmitted at high voltage so that the current, and so the I2RI^2R heating in the cables, is small.

Worked examples

Example 1: Force on a wire in a field

A straight wire 0.50 m long carries a current of 4.0 A in a uniform magnetic field of 0.20 T. Find the force on the wire when it is (a) perpendicular to the field, (b) at 30∘30^\circ to the field, (c) parallel to the field.

  1. (a) sin⁡90∘=1\sin 90^\circ = 1, so F=BIL=0.20×4.0×0.50=0.40 NF = BIL = 0.20 \times 4.0 \times 0.50 = 0.40\ \text{N}.

  2. (b) sin⁡30∘=12\sin 30^\circ = \frac{1}{2}, so F=0.40×12=0.20 NF = 0.40 \times \frac{1}{2} = 0.20\ \text{N}.

  3. (c) sin⁡0∘=0\sin 0^\circ = 0, so there is no force.

Answer

The forces are 0.40 N, 0.20 N and zero. Using cos⁡30∘\cos 30^\circ in (b) gives about 0.35 N, the tempting wrong answer: in BILsin⁡θBIL\sin\theta the angle is between the wire and the field.

Example 2: The emf from a falling field

A coil of 100 turns, each of area 0.020 m20.020\ \text{m}^2, lies with its plane perpendicular to a uniform magnetic field. The field falls steadily from 0.50 T to 0.10 T in 0.20 s. Find the average induced emf, and the current if the coil's circuit has a total resistance of 2.0 Ω2.0\ \Omega.

  1. Flux through one turn: before, 0.50×0.020=0.010 Wb0.50 \times 0.020 = 0.010\ \text{Wb}; after, 0.10×0.020=0.0020 Wb0.10 \times 0.020 = 0.0020\ \text{Wb}. The change is ΔΦ=0.0080 Wb\Delta\Phi = 0.0080\ \text{Wb}.

  2. Faraday's law: ε=NΔΦΔt=100×0.00800.20=4.0 V\varepsilon = N\frac{\Delta\Phi}{\Delta t} = 100 \times \frac{0.0080}{0.20} = 4.0\ \text{V}.

  3. Check by a second route: the field changes at 0.400.20=2.0 T/s\frac{0.40}{0.20} = 2.0\ \text{T/s}, so ε=NAΔBΔt=100×0.020×2.0=4.0 V\varepsilon = NA\frac{\Delta B}{\Delta t} = 100 \times 0.020 \times 2.0 = 4.0\ \text{V}.

  4. Current: I=4.02.0=2.0 AI = \frac{4.0}{2.0} = 2.0\ \text{A}. By Lenz's law it flows so that its own field points the same way as the original field, opposing the decrease.

Answer

The average emf is 4.0 V and the current 2.0 A. Using only the final field, 100×0.00200.20=1.0 V100 \times \frac{0.0020}{0.20} = 1.0\ \text{V}, is the tempting wrong answer: the emf comes from the change of flux, not from the flux itself.

Example 3: Stepping down the mains

An ideal transformer has 1200 turns on its primary coil, connected to a 240 V alternating supply, and 60 turns on its secondary coil. What is the secondary voltage? If the secondary delivers 2.0 A, what current flows in the primary?

  1. Turns ratio: Vs=240×601200=12 VV_s = 240 \times \frac{60}{1200} = 12\ \text{V}.

  2. Power out: 12×2.0=24 W12 \times 2.0 = 24\ \text{W}. An ideal transformer loses nothing, so the power in is also 24 W.

  3. Primary current: Ip=24240=0.10 AI_p = \frac{24}{240} = 0.10\ \text{A}. Check with the inverse turns ratio: 2.0×601200=0.10 A2.0 \times \frac{60}{1200} = 0.10\ \text{A}.

Answer

The secondary voltage is 12 V and the primary current 0.10 A. Scaling the current by the same factor of 20 as the voltage, the wrong way round, gives 40 A in the primary, which would draw 9600 W from the mains to deliver 24 W.

Common traps

  • Expecting a magnetic force to change the speed

    A magnetic force on a moving charge is always perpendicular to its velocity, so it does no work. It can bend the path into a circle, but the speed and kinetic energy stay the same. Any option in which a magnetic field alone speeds up a charge is wrong.

  • Expecting an emf from a steady field

    A coil sitting still in a strong but constant field has no induced emf. Induction needs a change of flux: a changing field, a changing area or a change of orientation.

  • Using the wrong angle

    In F=BILsin⁡θF = BIL\sin\theta and F=qvBsin⁡θF = qvB\sin\theta, θ\theta is the angle between the wire (or velocity) and the field. In Φ=BAcos⁡θ\Phi = BA\cos\theta, θ\theta is the angle between the field and the normal to the area. A coil whose plane is perpendicular to the field has the maximum flux.

  • Thinking a step-up transformer creates power

    Raising the voltage by a factor lowers the current by the same factor, so VIVI stays the same in an ideal transformer, and is a little smaller in a real one. A transformer also needs alternating current; with steady direct current the secondary voltage is zero.

Check yourself

Choose an answer to each question: you will see at once whether it is right, and why.

Question 1: A proton crossing a field

Magnetism

A proton (charge 1.6×10−19 C1.6 \times 10^{-19}\ \text{C}) moves at 2.0×106 m/s2.0 \times 10^6\ \text{m/s} at right angles to a uniform magnetic field of 0.50 T. Which statement is correct?

Show the answer

Answer: C. The force on it is 1.6×10−13 N1.6 \times 10^{-13}\ \text{N}, and its speed stays constant.

Working

F=qvB=1.6×10−19×2.0×106×0.50=1.6×10−13 NF = qvB = 1.6 \times 10^{-19} \times 2.0 \times 10^6 \times 0.50 = 1.6 \times 10^{-13}\ \text{N}. The force is perpendicular to the velocity, so it does no work: the proton moves in a circle at constant speed.

Why the other options are wrong

  • A. The force is zero only for motion along the field; here the motion is perpendicular to the field, where the force is greatest.
  • B. The size is right, but a force perpendicular to the velocity does no work, so the speed cannot change.
  • D. This is qvqv without the field; multiplying by B=0.50 TB = 0.50\ \text{T} halves it.
  • E. Divides qvqv by BB instead of multiplying by it.

What carries over

A magnetic force on a moving charge bends its path but never changes its speed.

Question 2: Turning a coil in a field

Electromagnetic induction

A 50-turn coil of area 0.040 m20.040\ \text{m}^2 lies with its plane perpendicular to a uniform 0.30 T field. In 0.10 s it is turned so that its plane is parallel to the field. What is the average emf induced?

Show the answer

Answer: D. 6.0 V

Working

The flux through one turn starts at BA=0.30×0.040=0.012 WbBA = 0.30 \times 0.040 = 0.012\ \text{Wb} and ends at zero. So ε=NΔΦΔt=50×0.0120.10=6.0 V\varepsilon = N\frac{\Delta\Phi}{\Delta t} = 50 \times \frac{0.012}{0.10} = 6.0\ \text{V}.

Why the other options are wrong

  • A. The field does not change, but the flux through the coil does, from BABA to zero; a change of flux is all that Faraday's law needs.
  • B. Leaves out the 50 turns; each turn has this emf, and the turns add up.
  • C. This is N ΔΦN\,\Delta\Phi, the change of flux linkage, not yet divided by the 0.10 s.
  • E. Treats the flux as reversing from +BA+BA to −BA-BA, which would need a half turn; this quarter turn takes it from BABA to zero.

What carries over

Any change of flux induces an emf, whether the field, the area or the orientation changes.

Question 3: An ideal step-up transformer

Electromagnetic induction

An ideal transformer has 200 turns on its primary coil and 1000 turns on its secondary coil. The primary is connected to a 24 V alternating supply and carries 5.0 A. What are the secondary voltage and current?

Show the answer

Answer: D. 120 V and 1.0 A

Working

Vs=24×1000200=120 VV_s = 24 \times \frac{1000}{200} = 120\ \text{V}. The input power is 24×5.0=120 W24 \times 5.0 = 120\ \text{W}, and an ideal transformer delivers all of it, so Is=120120=1.0 AI_s = \frac{120}{120} = 1.0\ \text{A}. Check: the current falls by the same factor of 5 by which the voltage rises.

Why the other options are wrong

  • A. Inverts the turns ratio; with more turns on the secondary, the voltage goes up and the current goes down.
  • B. Scales the current up with the voltage; the output power would be 3000 W from 120 W in.
  • C. Keeps the current unchanged; the output power would be 600 W, five times the input.
  • E. The current is right, but the voltage ratio is inverted: the coil with more turns has the larger voltage.

What carries over

An ideal transformer changes voltage and current by inverse factors, keeping VIVI the same.

Flashcards

Recall the answer before you flip each card, then say whether you knew it. Cards you miss come back at the end.

Force on a moving charge in a magnetic field
F=qvBsin⁡θF = qvB\sin\theta, perpendicular to both vv and BB; zero for motion along the field. It does no work.
Force on a current-carrying wire
F=BILsin⁡θF = BIL\sin\theta, with θ\theta the angle between the wire and the field.
Field of a long straight wire
B=μ0I2πrB = \frac{\mu_0 I}{2\pi r}; the field lines are circles round the wire, in the direction given by the right-hand grip rule.
Magnetic flux
Φ=BAcos⁡θ\Phi = BA\cos\theta, in webers, with θ\theta the angle between the field and the normal to the area.
Faraday's and Lenz's laws
ε=−NΔΦΔt\varepsilon = -N\frac{\Delta\Phi}{\Delta t}; the induced current flows so as to oppose the change of flux that causes it.
The ideal transformer
VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p} and VpIp=VsIsV_pI_p = V_sI_s. It works only with alternating current.

Key points

  • The magnetic force on a moving charge is qvBsin⁡θqvB\sin\theta, perpendicular to the velocity, so it does no work.

  • A wire carrying a current II across a field feels a force BILsin⁡θBIL\sin\theta.

  • Currents make magnetic fields: circles round a straight wire, a nearly uniform field inside a solenoid.

  • An emf is induced only while the flux changes, ε=−NΔΦΔt\varepsilon = -N\frac{\Delta\Phi}{\Delta t}, and the induced current opposes the change.

  • An ideal transformer obeys VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p} and keeps VIVI constant.

All questions here are original and written for UniExamer; none comes from the test maker.

Written and reviewed by the UniExamer education and assessment team. Every worked example and check question was checked before publication. If you find a mistake, write to support@uniexamer.com.

Practise this topic

Fresh questions on this skill, with worked explanations. Practice needs a Single Exam Pass or Plus.